CABLE DRUM Insert the 1/2-13 x 2” socket head cap screw into the drum shaft. APPLY GREASE TO DRUM SHAFT FLANGE Apply grease to both sides and outer diameter of the flange of the drum shaft. Be sure to check the identification on each drum to make sure the correct drum is installed on its corresponding side. DRUM SHAFT Cable drums are right and left. Align the left hand flag bracket to the existing left flag angle, so the top flange will be located to the top edge of the existing flag angle.ġ/2-13 X 2” SOCKET HEAD CAP SCREW Step 5: Cable Drum Installation NOTE: Do not remove shrink wrap from cable drums until instructed to do so. The right side bracket has an extended flange at the top. HOLES TO MATCH SLOTS IN FLAG BRACKETS There are two flag brackets (left and right) provided. Step 4: Flag Bracket Installation RIGHT HAND FLAG BRACKET 5/16 X 1-5/8” LAG SCREW DRILL (2) 3/8” DIA. Leave extension spring with it’s sheave installed. Carefully unfasten the S-hook from the horizontal angle. By opening the door, you release most of the spring tension. Idrive™ Retro-fit Installation Step 1: Extension Spring Relief Raise the door to the fully open position and clamp locking pliers to the back legs of both vertical tracks, below the bottom rollers to prevent the door from falling (see Fig. Tools Needed: 1/8” Drill Bit 3/32” Drill Bit Tape Measure Power Drill Pencil 7/16” Socket 1/2” Socket 9/16” Socket 3/4” Socket Step Ladder 7/16” Wrench 1/2” Wrench 9/16” Wrench 3/4” Wrench Flat Head Screwdriver 7/16” Socket Driver Safety Glasses Phillips Head Screwdriver 3/8” Hex Wrench Ratchet Locking Pliers (2) Level Available Accessories: For idrive™ 3-Button Mini RF Transmitter Model no: 3973 Part no: 302083 Keyless Entry RF Transmitter Model no: KEP2 Part no: 302078 Low Headroom Kit Part Idrive™ Package Contents: 6’ Power Cord (1) Opener Three-button Transmitter (2) Wall Station Assembly Support Bracket Wall Station Reference Label Light Fixture Assembly w/ Screw & Diffuser Lock Arm Assembly Entrapment Label Owners Manual idrive™ Hardware Kit: 1/4 x 1-1/2” Hex Head Lag Screws (4) Disconnect Handle (1) “S” Hook (1) Disconnect Cable (1) M5 x. Package Contents: 3982 idrive™ Extension Spring Kit RH. These limits are designed to provide reasonable protection against harmful interference in a residential installation. NOTE: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of FCC Rules. Table of Contents System Requirements Important Safety Instructions Package Contents Tools Needed Available Accessories idrive™ Retro-fit Installation Extension idrive™ Installation Pre-Operation Installation Operation Maintenance Troubleshooting Warranty Customer Service Number 2. Use these instructions to install the extension spring kit with idrive™ Models: 3660-372/ 3661-372/ 3662-372/ 3760-372 Covered under one or more of the following U.S. Hope, OH 44660 (888) 827-3667 Installation Instructions and Owner’s Manual Model 3982 idrive™ Extension Spring Kit. It's also a compatible safety sensor system replacement for Wayne Dalton Door Master models 3660-372, 3661-372, 3662-372, 2.N SI O N TE EX Wayne-Dalton Corp. The WD-252118 is a compatible safety sensor system replacement for Wayne Dalton iDrive models 3651-372 and 370-372. The WD-252118 Wayne Dalton infrared safety sensor kit includes sensors, brackets, wires and fasteners for easy installation. The Wayne Dalton WD-252118 wired infrared safety sensor kit from Garage Door Supply Company is a replacement safety sensor system for Wayne Dalton iDrive, Quantum, Door Master and Classic Drive model garage door openers. Gate Opener Remotes, Keypads, Radio Receivers.Genie Aladdin Connect Smart Phone System.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |